Home Electronics & hamradio Antennas Quagi 8 elements 432MHz
Quagi 8 elements 432MHz PDF Print
Written by Administrator   
Sunday, 26 April 2009 00:00

I like electronics, telecommunications, photography, playing various instruments, programming... There are a couple of recent projects that I'd like to show to you. Let's begin with a 432 Mhz Quagi antenna.

I tried N6NB's project but it didn't work well. Actually, there were some differences from the original project: for the Driven Element and the reflector, I used 1.8mm solid copper wire (the one for coils or transformers) because, at least in Italy, the old insulated #12 TW solid copper wire is too hard to be found. Furthermore, the Directors diameter was 4mm instead of 3mm. Probably these differences resulted in unacceptable Standing Wave Ratio, as you can see here below:

Fig. 1 Experimental SWR curve obtained with N6NB's design (materials as specified in the text above)

 

 

 

 

Someone suggested me to optimize the antenna through NEC2, and... here you are the first results.

This Quagi is optimized for 432.2Mhz operation, however it works well in a quite wide range of frequency. All following data are obtained through 4NEC2D v. 5.3.2 by Arie.

The protype behaves better than I expected, but it seems that the Driven Element requires a little adjustement due to mounting approximations and to the coating of the copper wire. In my prototype, the Driven Element required to be shortened of about 3mm.

I suggest to:

1) Build the antenna by using the design data here below

2) Run a SWR curve

3) Adjust the DE length. An estimation of the new length is: DE(new) = DE(old) * fSWRmin/432.2

where fSWRmin is the new frequency in MHz of minimum SWR. However the actual length depends on your peculiar construction, thus take it easy and don't cut too much!

I put some experimental results and the pictures of the prototype at the bottom of this page. I only regret that I did not record the SWR curves taken when the Driven Element was 741mm and 738mm long, however you can see that with 735mm the minimum SWR is @ 434.5MHz. You can also see the comparison to a simulated antenna with 735mm DE which includes loss due to non-ideal material.

 

 

Have fun!

 

Parameter

Value

Unit (Conditions)

Frequency

432.2

MHz

Gain

13.77

dBi in free space

SWR

1:1.03

(432.2 MHz)

SWR (min)

1.01

(432 MHz)

Bandwidth

430-434

MHz (SWR<1.4:1)

Take off angle

1.8

Degrees above a good ground (antenna height, about 8 wavelengths)

Table 1 Antenna performance (MOM simulation)

 

 

struttura quagi ik1hge 8el 432 Mhz

Fig. 2 Structure of the Quagi antenna

 

 

Copper wire diameter for the square elements

0.0018

Aluminum directors diameter:

0.004

Boom (wood): 1.50

Element

Length

Position

 

Spacing

RE

0.76215

-0.22904

DE-RE

0.22904

DE

0.7413

0

DE-DE

0

D1

0.29365

0.13093

DE-D1

0.13093

D2

0.29213

0.40783

D1-D2

0.2769

D3

0.28042

0.57751

D2-D3

0.16968

D4

0.28618

0.7632

D3-D4

0.18569

D5

0.28384

1.0228

D4-D5

0.2596

D6

0.27414

1.2687

D5-D6

0.2459

Tab. 2 Design details (meters)

 

Fig. 3 Vertical (Elevation) pattern in free space

 

 

diagramma di radiazione orizzontale

Fig. 4 Horizontal radiation pattern in free space (horizontal component)

 

 

Fig. 5 SWR and reflecttion coefficient charts

 

 

quagi 8el 432Mhz grafici impedenza in funzione della dfrequenza

Fig. 6 Impedance charts: Resistance,Reactance (top) and Impedance,Phase (bottom)

 

quagi 8el 432MHz grafico del guadagno in funzione della frequenza

Fig. 7 Total Gain vs. Frequency

 

Fig. 8 IK1HGE 432MHz 8el Quagi - 3D horizontal gain plot

The construction details are described in N6NB's article, in the ARRL Antenna Handbook and in many places on the net. Just search for "Quagi".

Here below, find some suggestions and some pictures of my prototype.

  • Use some kind of coating to protect the boom from humidity and sun.

  • To hold each square, I used two strips of FR4, that is the normal substrate for Printed Circuit Boards (completely remove the copper foils first!)

  • The Driven Element is fed trough a female N connector and a short piece of RG213. Protect the connection points to the square. To make the conection more flexible, I suggest to use a thinner coax instead (like the RG58). You can then use the RG213 for the longer line connecting the RTX to the antenna.

  • After the directors are perfectly aligned, you can fix them with a drop of glue.

quagi 8 el 432MHz ik1hge, fotografia dell'antenna a montaggio ultimato

i due elementi quadrati della quagi: direttore e riflettorei due elementi quadrati visti da un'altra angolazioneparticolare della saldatura del cavo coassiale al direttore

Fig. 9 IK1HGE 432MHz 8el Quagi - Prototype construction details

I appreciate your comments about this project. For further information or to give me some feedback about your experimental version of this design, e-mail me:

This e-mail address is being protected from spambots. You need JavaScript enabled to view it

Last Updated on Friday, 04 June 2010 12:01